The Best .410 Reloading Press for the Money

Most Accurate Reloading Press for the Money
Photo by David/ CC BY

If you have ever used a 410 you know that it’s nothing like a pistol shell. That is why you need the best .410 reloading press to get the best possible reload quality.

A competitive shooter goes through a lot of ammunition, and with a 410 the cost gets up quickly so it’s not practical to buy new ammo when you run out. That’s why it is better to buy a 410 reloading press so you will save a lot of money.

To help you decide what to buy I spent hundreds of hours testing and reviewing these products and these came out on top..

Best Picks of .410 Reloading Press

#1: MEC 600 Jr Mark V 410 Press- 2.5″ Shell

MAYVILLE ENGINEERING MEC 600 Jr Mark V 410 Press- 2.5" Shell

MEC 600 Jr Mark V 410 Press- 2.5" Shell
  • 8447410 600 Jr
  • Series mark V shot shell reloaded
  • Type shot shell reloading press
The Mayville 410 shotshell reloader is an easy to use single stage shotshell press. It is ideal for different shooters as you just can quickly adjust it to suit 3 or 2.5-inch shells.

The level of adjustability on the Mayville is hard to match and that’s what gives it the advantage. Handloading set up is faster here and that makes a huge difference when it comes to production.

The Mayville shotshell reloader is equipped with cam action crimp to make certain the shell is in good condition. The reloader also comes with a Spandex Camp Starter swivel so it is correctly aligned with the shell marks.

The reloader doesn’t come with dies, but you do get a shot charge bar and 3 powder bushings. It’s also easy to use as you just put one primer in the station, pull down the lever and the primer gets seated.

The reloader is also fast and efficient. Once it’s been loaded you can reload up to 400 rounds in three hours or less. Lastly, the reloader is very easy to use.

The Mayville reloader is a no frills product but it gets the job done. Compared to buying new 410 ammo, you’ll be able to save a lot of money and time.

Highlighted Features
  • Loads 6 to 8 boxes an hour
  • Can be upgraded to 285 CA
  • May be adjusted to 3 inch shells
  • Wad positioning is easy
  • Loads 2 1/2 shells

#2: MEC 650N .410 Press

MEC 650N .410 Press

MEC 650N .410 Press
  • Works on 6 shells at once
  • With every stroke a reloaded shell is completed
  • This product is manufactured in China
The 410GA reloading press was built expressly for the competitive shooter. While it is classified as affordable consumer grade that doesn’t mean it’s of low quality.

This 410 shotgun reloading press is for those who shoot plenty of shells. Design wise it is similar to the typical progressive press where a handle pull completes a shell.

The 410GA does not do hull resizing or inspecting so you’ll need to buy a separate sizer to perform this task. When used with a compatible sizer you’ll have no trouble using this to reload bullets.

The 410GA also comes with crimping stations that make certain the shells are of high quality and come out consistently. MEC has earned a solid reputation for quality and this product is a good example of that.

The 410GA does not come with dies but several die sets for it are available. Once you have the dies you can use it to reload shotgun shells. The reloader is not only fast but effective too as it can work on up to 6 shells simultaneously.

The 3 crimping stations work together well. The first commences the crimping process while the second shuts the crimp down. The third crimp puts the taper on a shell so correct feeding is done.

Highlighted Features
  • Can be used on up to 6 shells at the same time
  • Efficient strokes for faster production
  • Easy to use even for a new user
  • Made from durable parts and built to last
  • 3 crimping stations included

 

What is the Best .410 Reloading Press?

Deciding what 410 reloading press is best depends on your needs.  I can say based on my experience that the two products reviewed here are the most effective. I will pick out a winner from the two later on, but they’re both good.

Why Buy a .410 Reloading Press?

There are a lot of reasons that may be given, but what it comes down to is you’ll save money. 410 ammo are not easy to find and you often have to buy them from a specialty store.

Needless to say, that makes 410 ammo costly and impractical for shooting practice. If you’re going to spend a lot of time shooting hundreds or thousands of rounds, you’ve got to find a cheaper option.

That is where a 410 reloading press comes into play. With this, you’ll be able to reload shotgun shells and reuse them.

Difference between Shotgun Shells and Other Ammo?

There are several differences between 410 and regular ammunition, chief among them is the cost as 410 shells are more expensive. While ordinary ammo can be used on almost any type of reloading press, 410 shotgun shells need specialized reloading presses like these to run properly.

Another difference is that shotgun shells have less brass in the shell. Rather than the brass majority of the material is comprised of plastic. This plastic material is reusable so you’ll be able to save money. To be able to take advantage of reusable casings, you’ll need to buy a 410 reloading press.

 

Things to Consider Before Buying a .410 Reloading Press

There was a time when you could purchase kits that would let you reload 401 shotgun shells on a single stage press. However, these kits have become difficult to find so it may not be practical to use them.

If you’re going to reload a lot of shotgun shells make sure you’ve got the right reloading press. What this means is the press must state specifically that it’s designed for 410 shotgun shells.

A dedicated press is not enough as you have to make sure that it’s got the features you’re looking for.

Shell Compatibility

Some 410 reloading presses only work with 2.5 inch or 3-inch shells. However, it’s best if you look for one that supports both as it gives you more flexibility.

Reloading presses with support for both can be adjusted to fit the shell you’re reloading. This feature only increases its versatility so you can reload more types of shotgun shells.

A well-made reload press should also have support for most if not all shotgun gauges.  Even if you work mostly with the 410 it won’t hurt if there’s support for other shells.

Ease of Use

An experienced reloader can churn out 150 shells or more in an hour especially if the press is easy to use.

 

Final Verdict

Deciding which of the two reloading presses here is better was hard, but in the end I had to give to the
Mayville Engineering 0810028. unlike other reloading presses, this is easy to use and comes with the features you need to churn out plenty of shells.

I also like that the Mayville Engineering is compatible with different types of shotgun shells.  With a simple tweak you can adjust the tool to suit the shell you’re working out.

Shooting with 410 shells doesn’t have to be costly. As long as you have a reloading press then you’ll have an easier time reloading shells. The Mayville Engineering lets you do that better than others so it’s the best .410 reloading press today.

Leave a Comment